View FI1216MF_137568.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BU TUNERS
DATA SHEET
www..com
FI1216MF MK2 Desktop video tuner multi system CCIR L/L' and B/G
Preliminary specification File under BU Tuners, DC03 1996 Jul 09
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
FEATURES * Systems CCIR L/L' and B/G * True 5 V device (low power dissipation) * Full frequency range from channel 2 (48.25 MHz) to channel 69 (855.25 MHz) * PLL controlled tuning
www..com * True-synchronous vision IF demodulator (PLL)
FI1216MF MK2
* Demodulated video output, AF sound output, second sound IF output * I2C-bus control of tuning, address selection, AFC status information * Complies with European regulations on radiation, signal handling and immunity ("CENELEC 55020, 55013") * Small horizontally mounted metal housing. DESCRIPTION The FI1200MK2 family of front ends are designed to meet a wide range of RF applications in the PC Multi-Media environment. The FI1216MF MK2 type are available with a single 75 input for TV reception. The input connector is available in either standard phono (female socket) or IEC (female socket). The tuning and bandswitching are performed through the built-in digitally controlled I2C-bus. All front ends meet the input immunity and radiation requirements of CENELEC. ORDERING INFORMATION TYPE FI1216MF MK2/HM/PH FI1216MF MK2/HM/IEC MARKING The following items of information are printed on a sticker that is on the top cover of the tuner: * Type number * Code number * Origin letter of factory * Change code * Year and week code.
The FI1216MF MK2 consists of a tuner section and an IF section, which are all designed on a single PCB. The front-end is assembled in a metal housing made of a rectangular tin plated steel frame with front and rear covers which have soldered contacts to the frame. A single phono or IEC aerial socket is mounted on one side of the frame. All other connections are made via pins at the bottom. The tuner section is equipped with 3 tuned RF MOSFET input stages, with a 3-band mixer-oscillator IC, containing the oscillators, mixers and IF amplifier. Tuning and band switching in the tuner section are done with a digital programmable PLL tuning system. This enables tuning with step-size programmable between 31.25, 50.0 or 62.5 kHz. A DC-DC converter is built around the PLL synthesizer IC to provide the tuning voltage, thus making the FI1216MF MK2 front-end a true 5 V device. The IF section uses a true-synchronous vision IF demodulator (PLL) with an intercarrier SAW filter in front of it. The analog AFC voltage is fed to the 5-level A/D converter in the PLL tuning IC, so that the AFC status can be read via the I2C-bus.
DESCRIPTION standard phono IEC
CATALOGUE NUMBERS 3139 147 13571 3139 147 13581
1996 Jul 09
2
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
INTERMEDIATE FREQUENCIES FREQUENCY(1) (MHz) L Picture carrier Colour www..com Sound 1 Sound 2 NICAM Note 1. The oscillator frequency is above the input signal frequency. CHANNEL COVERAGE BAND Low band Mid band High band PINNING SYMBOL VT VS SCL SDA AS n.c. 2nd IF CVBS VIF AF sound output - sound output PIN 11 12 13 14 15 21 22 23 24 25 TH1, TH2, TH3 and TH4 48.25 to 170.00 MHz 170.00 to 450.00 MHz 450.00 to 855.25 MHz 38.90 34.47 32.40 - 33.05 L' 33.95 38.38 40.45 - 39.80
FI1216MF MK2
SYSTEM
PAL B/G 38.90 34.47 33.40 33.16 33.05
CHANNELS
DESCRIPTION tuning voltage (monitor) supply voltage tuner section +5 V I2C-bus serial clock I2C-bus serial data I2C-bus address select not connected second IF sound output Composite Video Baseband Signal output supply voltage IF section +5 V AF sound output mounting tags (ground)
1996 Jul 09
3
www..com
handbook, full pagewidth
1996 Jul 09
MIXER - OSCILLATOR IC IF VCO 77.8/67.9 MHz
BLOCK DIAGRAM
Philips Components
HIGH BAND
L'
HIGH OSC. BAND
L
MID BAND MID OSC. BAND VIF PLL DEMODULATOR
Desktop video tuner multi system CCIR L/L' and B/G
LOW OSC. BAND
LOW BAND
4
FILTER TRAP
L
L'
AGC
AM DEMODULATOR
DC - DC
PLL
+ADC
12
11
13
14
15
L
L'
22
23
24
25
CCA217
VS VT SCL SDA AS 2nd IF sound output CVBS VIF (+5 V) AF sound output
(+5 V)
FI1216MF MK2
Preliminary specification
Fig.1 Electrical block diagram.
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
LIMITING VALUES Limiting values under operational conditions The tuner can be guaranteed to function properly under the following conditions. SYMBOL VS VS(ripple) supply voltage peak-to-peak ripple voltage susceptibility (at 5 V 5%); note 1 20 Hz to 100 kHz >100 kHz to 500 kHz IS VSCL VSDA ISDA VAS ZIF supply current SCL bus input voltage SDA bus input voltage SDA bus current (open collector) address select voltage; note 2 2nd IF sound output load impedance: DC AC ZCVBS Composite Video Baseband Signal load impedance: DC AC tL VIF VIF(ripple) load time constant IF supply voltage peak-to-peak ripple voltage susceptibility (at 5 V 5%); note 1 20 Hz to 100 kHz >100 kHz to 500 kHz IIF ZAF IF supply current AF sound output load impedance: DC AC Notes 25 1.0 0.6 - - 23 - - - 4.75 22 0.5 0.5 - - 13 14 15 PARAMETER PIN MIN. 4.75
FI1216MF MK2
TYP. 5.00
MAX. 5.25
UNIT V
www..com
12
- - - -0.3 -0.3 -1 -
- - - - - - -
20 10 120 +5.25 +5.25 +5 +5.25 - -
mV mV mA V V mA V k k
75 75 - 5.0
- - 100 5.25
ns V
24
- - -
- - -
20 10 100 - -
mV mV mA k k
1. Sinusoidal ripple voltage superimposed on the 5 V supply voltage in the frequency range of 20 Hz to 500 kHz. Criteria for TV interference >57 dB. 2. For detailed information about the address decoding, refer to Chapter "Application information".
1996 Jul 09
5
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Environmental conditions SYMBOL PARAMETER CONDITIONS MIN. -25 - 25 g 50 g 10 to 55 Hz - - - -10 - - - - - 0.35 - - TYP.
FI1216MF MK2
MAX. C %
UNIT
Non-operational conditions Tamb RH
www..com
ambient temperature relative humidity bump acceleration shock acceleration vibration amplitude
+85 100 245 490 -
gB gS
m/s2 m/s2 mm C %
Operational conditions Tamb RH ambient temperature relative humidity +60 95
OVERALL PERFORMANCE Conditional data Unless otherwise specified, all electrical values for Chapter "Overall performance" apply at the following conditions. SYMBOL Tamb RH VS ZCVBS ZIF tpr ZS(AE) ambient temperature relative humidity supply voltage (tuner and IF section) video output load impedance (DC) IF sound output load impedance (DC) pre-heating time (+5 V at pin 24) aerial source impedance (unbalanced) PARAMETER VALUE 25 5 60 15 5 0.125 >75 >500 10 75 C % V minute UNIT
1996 Jul 09
6
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
TUNER SECTION Tuner characteristics
FI1216MF MK2
For detailed information about the PLL programming, refer to Chapter "Application information". The desktop video tuner is guaranteed to function properly within the specified operational conditions, but a certain deterioration of performance parameters may occur at the limits of the operational conditions.
www..com Test equipment
EQUIPMENT DC voltmeter Oscilloscope input impedance input impedance: resistance capacitance Spectrum analyzer FET probe input impedance input impedance: resistance capacitance output impedance voltage gain
PARAMETER >1 >1
VALUE M M pF M pF dB
UNIT
<15 50 1 3.5 50 0
1996 Jul 09
7
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
FI1216MF MK2
handbook, full pagewidth
aerial connector
www..com
TP2 11 12 13 14 15
TP3 22 23 24 25
IF output
IF PROBE OUT
VT BU2 VS SCL SDA
1 nF 3 k
10 nF
33 F
TEST JIG
BU5 BU4 video out P 51 nF 1 k
(2) (1)
BU2 +5 V
BU6
SA
DA
CCA010
(1) BU4 loaded with 75 . (2) 50 s de-emphasis. SA = spectrum analyzer. P = FET probe. DA = distortion analyzer.
Fig.2 Typical test set-up.
1996 Jul 09
8
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Definitions of test signals (see Fig.2) TEST SIGNAL A0: unmodulated vision carrier A1: L system signal with
www..com video modulation; see note 1
FI1216MF MK2
FREQ. (MHz) 480.25 480.25 480.25 480.25
MODULATION AMPLITUDE VIDEO 60 dBV 60 dBV (peak white) 60 dBV (top sync) 60 dBV 100% (sync. level at 0%) 2T pulse and bar 100% (rest carrier 10%) 2T pulse and bar 100% (rest carrier 10%) 15625 kHz horizontal frequency square wave AUDIO
A2: B/G system signal with video modulation A3: B/G system signal with video modulation B1: unmodulated main sound carrier B/G system B2: AM modulated sound carrier L system B3 FM modulated main sound carrier B/G system B4: unmodulated second sound carrier B/G system Note
485.75 486.75 485.75
-13 dB w.r.t. A2 -10 dB w.r.t. A0 to A1 -13 dB w.r.t. A2 m = 0.54; modulation frequency 1 kHz 1 kHz; modulation frequency deviation 27 kHz; 50 s pre-emphasis
486.10
-20 dB w.r.t. A0 to A1
1. Line 17 and 330 shall always contain a composite video signal (ITS lines).
1996 Jul 09
9
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Aerial input characteristics SYMBOL VSWR PARAMETER reflection coefficient CONDITIONS referred to 75 impedance (worst case on or between picture and sound carrier at maximum gain) <1.75 GHz -
FI1216MF MK2
MIN. 5
MAX.
UNIT
VPSM Vant www..com
surge protection voltage antenna connection disturbance voltage
5 -
- 46
kV dBV
General characteristics SYMBOL fb PARAMETER frequency range: low band mid band high band margin: for low band for mid/high band image rejection (nominal gain to 10 dB gain reduction): low band mid band mid band high band IF rejection (picture) 1 IF susceptibility: 2 E2 to E12 E21 to E69 sound-chrominance moire rejection: off-air UHF cross modulation: in-channel in-band low band (n 2) mid band (n 3) high band (n 5) out of band breakthrough susceptibility: E2 to E12; E21 to E69 CONDITIONS MIN. 48.25 175.25 455.25 1.5 3 - - - - - TYP. MAX. 168.25 447.25 855.25 - - UNIT MHz MHz MHz MHz MHz
fb
i
<300 MHz >300 MHz
IF ZIF
70 66 60 50 60 75 60
- - - - - - - - -
- - - - - - - - -
dB dB dB dB dB dBV dBV dB dB
S
up to 40 dB gain control up to 30 dB minimum gain control
56 56
mx
70 78 78 84 - 60
- - - - 100 -
- - - - - -
dBV dBV dBV dBV dBV dBV
1996 Jul 09
10
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
SYMBOL Vosc tli vs PARAMETER oscillator voltage at all pins oscillators lock-in time the video signal-to-sound interference ratio with the tuner exposed to sound signals in the audio frequency range 100 Hz to 10 kHz and sound pressure levels up to 105 dB (20 Pa) electrostatic discharge (ESD) on all pins CONDITIONS MIN. - - -
FI1216MF MK2
TYP.
MAX. 70 150 -
UNIT dBV ms dB
- charge pump set logic HIGH - 40
www..com
VESD Note
note 1
2
-
-
kV
1. All the pins of the desktop video tuner are protected against electrostatic discharge (ESD) up to 2 kV. The product is classified in category B (``MIL-STD-883C").
1996 Jul 09
11
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Video and audio characteristics (see Fig.2) PARAMETER CVBS characteristics: video amplitude signal at pin 23 DC level sync pulse at pin 23
www..com Video amplitude drop with respect to modulation
FI1216MF MK2
TEST SIGNAL
TEST POINT BU4 BU4
MIN. TYP. MAX.
UNIT
A1 (peak-to-peak value) A1
0.7 -
0.9 0.35
1.1 -
V V
0.1 MHz at Tamb = 45 C: at 2 MHz at 3 MHz at 4 MHz at 4.43 MHz Sound carrier rejection Residual 40.4 MHz signal in video channel: level of 1.5 MHz Residual 77.8 MHz signal in video channel Second IF sound output level at level of 5.5 MHz Test on 2T pulse at Tamb = 45 C: 2T pulse/bar response for L mode 2T pulse response for L mode 2T pulse/bar response for B/G mode 2T pulse response for B/G mode CVBS S/N (unweighted) Gain limited sensitivity at 1 dB reduction of video output B/G audio characteristics: AF output level measured via LP 20 kHz filter, RMS detector, 50 s de-emphasis THD (Total Harmonic Distortion) measured via LP 20 kHz filter, RMS detector, 50 s de-emphasis S/N measured via CCIR filter, peak CCIR detector, 50 s de-emphasis L/L' audio characteristics: AF output level measured via LP 20 kHz filter, RMS detector THD (Total Harmonic Distortion) measured via LP 20 kHz filter, RMS detector S/N measured via CCIR filter, peak CCIR detector AM suppression ratio Aerial input level for S/N = 45 dB: system B/G system L 1996 Jul 09 A2 (black) + B3 A1 (black) + B2 12 BU4 BU4 - - 35 40 40 45 dBV dBV A1 + B2 A1 + B2 A1 (black) + B2 A1 + B2 BU6 BU6 BU6 BU6 0.40 - 41 40 0.50 0.7 46 - 0.60 1.5 - - V % dB dB A2 + B3 A2 + B3 BU6 BU6 0.25 - 0.35 0.15 0.50 0.5 V % A1 A1 A1 A1 A1 + B1 A3 BU4 BU4 BU4 BU4 BU4 BU4 -3.0 - -4.5 - 40 - - - - - - - +3.0 +3.0 +3.0 +5.0 - 30 % % % % dB dBV A1 A1 A1 A1 A1 + B3 A1 + B3 A2 A2 + B1 BU4 BU4 BU4 BU4 BU4 BU4 BU4 BU5 -1.5 -2.5 -4.0 -6.0 40 - - 84 - - - - - - - - +1.5 +1.5 +2.0 +2.0 - 68 80 - dB dB dB dB dB dBV dBV dBV
A2 (6 kHz sine wave, black-to-white) + B3
BU6
40
47
-
dB
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Digital AFC status PARAMETER ADC word at I2C-bus during read operation CONDITIONS input voltage at pin 10: 0.0 to 0.15VS input voltage at pin 10: 0.15 to 0.30VS input voltage at pin 10: 0.30 to 0.45VS
www..com
FI1216MF MK2
FREQUENCY DIGITAL (kHz) READ-OUT -125 -62.5 0 +62.5 +125 00 01 02 03 04
input voltage at pin 10: 0.45 to 0.60VS input voltage at pin 10: 0.60 to 1.00VS
1996 Jul 09
13
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
APPLICATION INFORMATION
FI1216MF MK2
A detailed description of the I2C-bus specification, with applications, is given in brochure ``The I2C-bus and how to use it''. This brochure may be ordered using the code number 9398 393 40011. WRITE mode BITS
www..com
BYTE
7 MSB 1 0 n7 1 P7
6 1 n14 n6 CP P6
5 0 n13 n5 T2 P5
4 0 n12 n4 T1 P4
3 0 n11 n3 T0 P3
2 MA1 n10 n2 RSA P2
1 MA0 n9 n1 RSB P1
0 LSB 0 n8 n0 OS P0
A(1) A A A A A
Address byte Program divider byte 1 Program divider byte 2 Control information byte 1 Control information byte 2 Note 1. A = Acknowledge. ADDRESS SELECTION VS = +5 V (PLL supply voltage) MA1 0 0 1 1 Note MA0 0 1 0 1
ADDRESS C0 C2 C4 C6
VOLTAGE AT PIN 15 (see note 1) 0 to 0.1VS 0.2 to 0.3VS 0.4 to 0.6VS 0.9VS to VS
1. If the AS pin is left floating, the internal bias will automatically set the address to C2. PROGRAMMABLE DIVIDER SETTINGS (BYTES 1 AND 2) Divider ratio: N = 16 x {fRF(pc) + fIF(pc)}, where (pc) is picture carrier and fRF and fIF are expressed in MHz fosc = N16 (MHz). N = (8192 x n13) + (4096 x n12) + (2048 x n11) + (1024 x n10) + (512 x n9) + (256 x n8) + (128 x n7) + (64 x n6) + (32 x n5) + (16 x n4) + (8 x n3) + (4 x n2) + (2 x n1) + n0 CONTROL BYTE Charge pump settings: CP = 1, for fast tuning CP = 0, for moderate speed tuning with slightly better residual oscillator FM. Test mode settings: T2 = T1 = 0; T0 = 1, for normal operation. PLL disabling: OS = 0, for normal operation OS = 1, for switching the charge pump to the high impedance state. 1996 Jul 09 14
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Ratio select bits RSA X 0 1 PORTS BYTE www..com BAND/ SYSTEM Band switching Low band Mid band High band System switching L L' B/G Notes 1. X = don't care; P0 to P7 are output ports on the PLL device. 2. P3 is a system switch output for customer applications. TELEGRAM EXAMPLES (WRITE MODE) Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop. Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop. Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Stop. Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Stop. Where: Start = start condition Adb = address byte Ack = acknowledge Db1 = divider byte 1 Db2 = divider byte 2 Cb = control byte Pb = ports byte Stop = stop condition. 1 0 1 1 1 0 see note 2 0 0 0 see note 2 0 1 1 1 0 1 BIT (see note 1) P0 P1 P2 P3 P4 P5 RSB 0 1 1 STEP SIZE 50 kHz 31.25 kHz (for slow picture search) 62.5 kHz (for normal picture search)
FI1216MF MK2
P6
P7
0 0 0
1 1 0
1996 Jul 09
15
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
FI1216MF MK2
Remark: for channel selection involving band switching, and to ensure smooth tuning to the desired channel without causing unnecessary charge pump action, it is recommended to consider the difference between wanted channel frequency (fw) and the current channel frequency (fc): * If fw > fc, use telegram as: Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop. * If fw > fc, use telegram as: Start www..com Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop. Unnecessary charge pump action will result in very low tuning voltage (VT 0 V) which may drive the oscillator to extreme conditions. READ mode The in-lock can be read by setting the R/W bit to 1. BITS BYTE Address byte Status byte Notes 1. POR = Power On Reset. POR is internally set to 1 in case VS drops below 3 V. The POR bit is reset when an end of data is detected by the PLL IC. 2. FL = In-lock flag; FL = 1: loop is phase-locked. The loop must be phase-locked during at least 8 periods of the internal 7.8125 kHz reference frequency before the FL flag is internally set to 1. 3. I2, I1 and I0 = digital information for I/O ports P2, P1 and P0 respectively. 4. A2, A1 and A0 = built-in 5-level A/D converter on I/O port P6. AFC information to the controller of the IF section is available on pin 10 (see Table "Digital AFC status"). 5. A = Acknowledge. TELEGRAM EXAMPLES (READ MODE) Start - Adb - Ack - STB - Ack - STB - - Stop (no Ack from processor = End-of-data). Start - Adb - Ack - STB - - Stop (no Ack from processor = End-of-data). Where: STB = Status byte. 7 MSB 1 POR(1) 6 1 FL(2) 5 0 I2(3) 4 0 I1(3) 3 0 I0(3) 2 MA1 A2(4) 1 MA0 A1(4) 0 LSB 1 A0(4) A(5) A A
1996 Jul 09
16
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Video buffer
handbook, halfpage
FI1216MF MK2
VCC R1 R3 100 15 C1 56 pF AS
www..com
R2
A video buffer is built into the video module to enable the unit to drive a 75 load directly. In case it is required to use the FI1216MF MK2 as a replacement for the FI1216 in the same videocard, it is necessary to replace the 75 series resistor in the video card by a 0 series resistor. At the same time the 22 k series resistor in the tuning supply must be removed. I2C-bus load
R4 100 R5 100
C2 56 pF 14
SDA
The FI1216MF MK2 contains a series resistor (R = 100 ) in the SCL and SDA lines. Both lines also have a capacitive load of typical 56 pF (see Fig.3).
13 C3 56 pF
SCL
PLL IC
MBH031
Fig.3 I2C-bus load.
1996 Jul 09
17
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
MECHANICAL DATA
33.7 +0.2 0 25.9 20.6 16.6 15.8 10.4
FI1216MF MK2
handbook, full pagewidth
www..com
9.7 11.5 30.8 31.6 34.2
(1)
27.6
+0.2 0
8.1 0.3 26.9
(1)
8.35
78.4 0.8 5.1 7.9 2.5 2 0.5
STANDARD PHONO CONNECTOR 14.4 0.2
(2)
11
4
14.7 59.2
IEC CONNECTOR 13.5 max 12.9 max 5.2 6 (2x) 1.5 (2x)
6.35
+0.10 -0.04 1 TH2
(0.6) 1.5 (2x)
8.5 0.2 3 (2x) TH4 11 12 13 14 15 21 22 4.445 84.5 89.2 45.4 41 TH3 23 24 25 1.1 5 2.6
34.7
38.5
28.55 2.6
0.64 x 0.64
MGB515 - 1
Dimensions in mm. (1) Standard phono socket female 75 . (2) Alternative IEC connection.
Fig.4 Mechanical outline FI versions.
1996 Jul 09
18
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
Aerial connections Standard-phono socket female 75 or IEC (female). Solderability The solderability of pins and mounting tags when tested initially and after 16 hours steam ageing in accordance with ``IEC 68-2-20'', test Ta, method 1 (solder bath 235 C www..com for 2 s), results in a wetted area of 95%. No de-wetting will occur when soldered at 260 C for 5 s. Resistance to soldering heat The product will not be damaged when tested in accordance with ``IEC 68-2-20'', test Tb, method 1A (solder bath 260 C for 10 1 s). Mass Approximately 50 g. Robustness of pins
FI1216MF MK2
The pins will not be damaged when tested in accordance with ``IEC 68-2-21'': * Test Ua1, tensile of 10 N in axial direction * Test Ua2, thrust of 4 N in axial direction. Punching pattern of chassis PCB Field rejects are often related to broken tag joints. Therefore, the following punching pattern is recommended (see Fig.5).
handbook, full pagewidth
78.4 3.4 2.3 2 0.9
34.7 unit contour
2.1
1.1 2.6
MGB514 - 1
14.7
4.445 59.2
Dimensions in mm.
Fig.5 Punching pattern seen from solder side.
1996 Jul 09
19
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
TV CHANNEL FREQUENCIES (MHz) CCIR cable Vision IF = 38.90 MHz; sound IF = 33.40 MHz. CHANNEL
www..com E2
FI1216MF MK2
FREQ. RANGE 47-54 54-61 61-68 68-75 75-82 82-89 104-111 111-118 118-125 125-132 132-139 139-146 146-153 153-160 160-167 167-174 174-181 181-188 188-195 195-202 202-209 209-216 216-223 223-230 230-237 237-244 244-251 251-258
PICTURE SOUND CARRIER CARRIER FREQUENCY FREQUENCY 48.25 55.25 62.25 69.25 76.25 83.25 105.25 112.25 119.25 126.25 133.25 140.25 147.25 154.25 161.25 168.25 175.25 182.25 189.25 196.25 203.25 210.25 217.25 224.25 231.25 238.25 245.25 252.25 53.75 60.75 67.75 74.75 81.75 88.75 110.75 117.75 124.75 131.75 138.75 145.75 152.75 159.75 166.75 173.75 180.75 187.75 194.75 201.75 208.75 215.75 222.75 229.75 236.75 243.75 250.75 257.75
CHANNEL S15 S16 S17 S18 S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 S29 S30 S31 S32 S33 S34 S35 S36 S37 S38 S39 S40 S41
FREQ. RANGE 258-265 265-272 272-279 279-286 286-293 293-300 302-310 310-318 318-326 326-334 334-342 342-350 350-358 358-366 366-374 374-382 382-390 390-398 398-406 406-414 414-422 422-430 430-438 438-446 446-454 454-462 462-470
PICTURE SOUND CARRIER CARRIER FREQUENCY FREQUENCY 259.25 266.25 273.25 280.25 287.25 294.25 303.25 311.25 319.25 327.25 335.25 343.25 351.25 359.25 367.25 375.25 383.25 391.25 399.25 407.25 415.25 423.25 431.25 439.25 447.25 455.25 463.25 264.75 271.75 278.75 285.75 292.75 299.75 308.75 316.75 324.75 332.75 340.75 348.75 356.75 364.75 372.75 380.75 388.75 396.75 404.75 412.75 420.75 428.75 436.75 444.75 452.75 460.75 468.75
E3 E4 S01 S02 S03 S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 E5 E6 E7 E8 E9 E10 E11 E12 S11 S12 S13 S14
1996 Jul 09
20
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
CCIR B/G Vision IF = 38.90 MHz; sound IF = 33.40 MHz. CHANNEL 2 3 www..com 4 5 6 7 8 9 10 11 12 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 FREQ. RANGE 47-54 54-61 61-68 174-181 181-188 188-195 195-202 202-209 209-216 216-223 223-230 470-478 478-486 486-494 494-502 502-510 510-518 518-526 526-534 534-542 542-550 550-558 558-566 566-574 574-582 582-590 590-598 598-606 606-614 614-622 PICTURE SOUND CARRIER CARRIER FREQUENCY FREQUENCY 48.25 55.25 62.25 175.25 182.25 189.25 196.25 203.25 210.25 217.25 224.25 471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.25 607.25 615.25 53.75 60.75 67.75 180.75 187.75 194.75 201.75 208.75 215.75 222.75 229.75 476.75 484.75 492.75 500.75 508.75 516.75 524.75 532.75 540.75 548.75 556.75 564.75 572.75 580.75 588.75 596.75 604.75 612.75 620.75 CHANNEL 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 FREQ. RANGE 622-630 630-638 638-646 646-654 654-662 662-670 670-678 678-686 686-694 694-702 702-710 710-718 718-726 726-734 734-742 742-750 750-758 758-766 766-774 774-782 782-790 790-798 798-806 806-814 814-822 822-830 830-838 838-846 846-854 854-862
FI1216MF MK2
PICTURE SOUND CARRIER CARRIER FREQUENCY FREQUENCY 623.25 631.25 639.25 647.25 655.25 663.25 671.25 679.25 687.25 695.25 703.25 711.25 719.25 727.25 735.25 743.25 751.25 759.25 767.25 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25 628.75 636.75 644.75 652.75 660.75 668.75 676.75 684.75 692.75 700.75 708.75 716.75 724.75 732.75 740.75 748.75 756.75 764.75 772.75 780.75 788.75 796.75 804.75 812.75 820.75 828.75 836.75 844.75 852.75 860.75
1996 Jul 09
21
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
France Vision IF = 38.90 MHz; sound IF = 32.40 MHz. CHANNEL FA FB www..com FC1 FC F1 F2 F3 F4 F5 F6 PICTURE SOUND CARRIER CARRIER FREQUENCY FREQUENCY 47.75 55.75 60.50 63.75 176.00 184.00 192.00 200.00 208.00 216.00 41.25 49.25 54.00 57.25 182.50 190.50 198.50 206.50 214.50 222.50
FI1216MF MK2
1996 Jul 09
22
Philips Components
Preliminary specification
Desktop video tuner multi system CCIR L/L' and B/G
DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification
www..com
FI1216MF MK2
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Application information Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011.
1996 Jul 09
23
Philips Components - a worldwide company
Argentina: IEROD, Av. Juramento, 1991-14.B, (1428) BUENOS AIRES, Tel. (541) 786 7635, Fax. (541) 786 9367. Australia: PHILIPS COMPONENTS PTY Ltd, 34 Waterloo Road, NORTH RYDE NSW 2113, Tel. (02) 805 4455, Fax. (02) 805 4466. Austria: PHILIPS COMPONENTS, Vertriebsgesellschaft m.b.H., Triester Strasse 64, A-1101 WIEN, P.O. Box 213, Tel. (01) 601 01 12 12, Fax. (01) 60 101 12 10. Belgium: PHILIPS NEDERLAND B.V., Philips Components & Semiconductors, Postbus 90050, 5600 PB EINDHOVEN, Netherlands, Tel. (31) 40 2783 749, Fax. (31) 40 2788 399. Belarus: PHILIPS OFFICE BELARUS, Hotel Minsk, Volodarski Str. 6, 220050 MINSK, Tel. (5172) 200 915, Fax. (5172) 200 773. Brazil: PHILIPS COMPONENTS, Rua do Rocio 220 - 5th floor, 04552-903 - SAO PAULO - SP, Tel. (011) 821 2333, Fax. (011) 829 1849. Canada: PHILIPS ELECTRONICS Ltd., Philips Components, 601 Milner Ave., SCARBOROUGH, Ontario, M1B 1M8, Tel. (0416) 292 5161, Fax. (0416) 754 6248. www..com Chile: PHILIPS CHILENA S.A., Av. Santa Maria 0760, SANTIAGO, Tel. (02) 77 38 16, Fax. (02) 735 35 94. China: PHILIPS COMPANY, Philips Components MSO PRC, 6/F Building 2 No. 889, Yi Shan Road, SHANGHAI 200233, Tel. (21) 485 0600, Fax. (21) 485 1015. Colombia: IPRELENSO LTDA, Diagonal 59, No. 20-27, P.O. Box 77621, SANTAFE DE BOGOTA, Tel. (57) (1) 345 8713, Fax. (57) (1) 345 8712. Denmark: PHILIPS COMPONENTS A/S, Prags Boulevard 80, P.O Box 1919, 2300 COPENHAGEN S, Tel. (32) 883 333, Fax. (31) 571 949. Finland: PHILIPS COMPONENTS, Sinikalliontie 3, FIN-02630 ESPOO, Tel. (9) 0-615 800, Fax. (9) 0-615 80920. France: PHILIPS COMPOSANTS, 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES, Cedex, Tel. (01) 4099 6161, Fax. (01) 4099 6427. Germany: PHILIPS COMPONENTS UB der Philips G.m.b.H., P.O. Box 10 63 23, 20043 HAMBURG, Tel. (040) 2489 1330, Fax. (040) 2489 1426. Greece: PHILIPS HELLENIQUE S.A., Components Division, No. 15, 25th March Street, GR 17778 TAVROS, Tel. (01) 4894 339/(01) 4894 911, Fax. (01) 4815 180. Hong Kong: PHILIPS HONG KONG, Components Division, Unit 003-005, G/F, Hong Kong Ind. Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, KOWLOON, Tel. (852) 2784 3000, Fax. (852) 2784 3003. India: Philips INDIA Ltd., Components Dept., Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, BOMBAY 400 018, Tel. (022) 4938 541, Fax. (022) 4938 722. Indonesia: P.T. PHILIPS DEVELOPMENT CORPORATION, Philips House, Jalan H.R. Rasuna Said Kav. 3-4, P.O. Box 4252, JAKARTA 12950, Tel. (021) 520 1122, Fax. (021) 520 5189. Ireland: PHILIPS ELECTRONICS (IRELAND) Ltd., Components Division, Newstead, Clonskeagh, DUBLIN 14, Tel. (01) 76 40 203, Fax. (01) 76 40 210. Israel: Rapac Electronics Ltd., 7 Kehilat Saloniki St. P.O. Box 18053, TEL AVIV 61180, Tel. (03) 6450 444, Fax. (03) 6491 007. Italy: PHILIPS COMPONENTS S.r.l., Piazza IV Novembre 3, 20124 MILANO, Tel. (02) 6752 2531, Fax. (02) 6752 2557. Japan: PHILIPS JAPAN Ltd., Components Division, Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. (03) 3740 5028, Fax. (03) 3740 0580. Korea (Republic of): PHILIPS ELECTRONICS (KOREA) Ltd., Components Division, Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. (02) 709 1472, Fax. (02) 709 1479. Malaysia: PHILIPS MALAYSIA SDN BERHAD, Components Division, No. 76 Jalan Universiti, 46200 Petaling Jaya, KUALA LUMPUR, Tel. (03) 757 5511, Fax. (03) 757 4880. PHILIPS MALAYSIA SDN BERHAD, Components Division, 345 Jalan Gelugor, PULAU PINANG, Tel. (04) 870 055, Fax. (04) 879 215. Mexico: PHILIPS COMPONENTS, 5900 Gateway East, Suite 200, EL PASO, TX 79905, U.S.A., Tel. (915) 772 4020, Fax. (915) 772 4332. Netherlands: PHILIPS NEDERLAND B.V., Philips Components & Semiconductors, Bldg. VB Postbus 90050, 5600 PB EINDHOVEN, Tel. (040) 2783 749, Fax. (040) 2788 399. New Zealand: PHILIPS NEW ZEALAND Ltd., Components Division, 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. (09) 849 4160, Fax. (09) 849 7811. Norway: NORSK A/S PHILIPS, Philips Components, Box 1, Manglerud 0612, OSLO, Tel. (22) 74 8000, Fax. (22) 74 8341. Pakistan: Philips Electrical Industries of Pakistan Ltd., Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton, KARACHI 75600, Tel. (021) 587 4641-49, Fax. (021) 577 035/587 4546. Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. (02) 810 0161, Fax. (02) 817 3474. Poland: PHILIPS POLAND Sp. z.o.o. Components Division, ul. Lutkiska 10, 04-123 WARSZAWA, Tel. (22) 612 2594, Fax. (22) 612 2327. Portugal: PHILIPS PORTUGUESA, S.A., Rua dr. Antonio Loureiro Borges 5, Arquiparque - Miraflores, Apartado 300, 2795 LINDA-A-VELHA, Tel. (01) 416 3160/416 3333, Fax. (01) 416 3174/416 3366. Russia: PHILIPS RUSSIA, ul. Usatcheva 35A, 119048 MOSCOW, Tel. (095) 926 5361, Fax. (095) 564 8323. Singapore: PHILIPS SINGAPORE, Pte Ltd., Components Division, Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. (65) 350 2000, Fax. (65) 355 1758. South Africa: S.A. PHILIPS Pty Ltd., Components Division, 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. (011) 470 5911, Fax. (011) 470 5494. Spain: PHILIPS COMPONENTS, Balmes 22, 08007 BARCELONA, Tel. (93) 301 63 12, Fax. (93) 301 42 43. Sweden: PHILIPS COMPONENTS AB, Kottbygatan 7, Akalla. Postal address: S-164 85 STOCKHOLM, Tel. (+46) 8 632 2000, Fax. (+46) 8 632 2745. Switzerland: PHILIPS COMPONENTS AG, Allmendstrasse 140, CH-8027 ZURICH, Tel. (01) 488 22 11, Fax. (01) 481 77 30. Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West Road, Sec. 1. Taipei, Taiwan ROC, P.O. Box 22978, TAIPEI 100, Tel. (02) 388 7666, Fax. (02) 382 4382. Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, Bangkok 10260, THAILAND, Tel. (66) 2 745 4090, Fax. (66) 2 398 0793. Turkey: Turk Philips Ticaret A.S., Components Department, Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. (0212) 279 2770, Fax. (0212) 282 6707. Ukraine: PHILIPS UKRAINE Ltd., 2A Akademika Koroleva str., 252148 KIEV, Tel. (044) 476 0297, Fax. (044) 476 6991. United Kingdom: PHILIPS COMPONENTS Ltd., The Mullard Building, Dorking Business Park, DORKING, Surrey, RH4 1HJ, Tel. (01306) 512 000, Fax: (01306) 512 345. United States: PHILIPS COMPONENTS, Division Headquarters, 1440 Indiantown Road, JUPITER, FL 33458, Tel. (561) 745 3300, Fax. (561) 745 3600. For literature: (800) 447 3762. PHILIPS DISPLAY COMPONENTS COMPANY, 1600 Huron Parkway, ANN ARBOR, Michigan 48105-2590, Tel. (313) 996 9400, Fax. (313) 761 2776. Uruguay: PHILIPS COMPONENTS, Coronel Mora 433, MONTEVIDEO, Tel. (02) 704 044, Fax. (02) 920 601. For all other countries apply to: Philips Components, Marketing Communications, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31-40-2724 547. COD06 (c) Philips Electronics N.V. 1996
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands

▲Up To Search▲

Price & Availability of FI1216MF

	To Download FI1216MF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .